View PC817XI5_8386039.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

h november 28, 1995 electronic compone group sharp corporation f \ device specification for business dealing name photocoupler model no. pc817 specification opto-elects devices div. 1. these specification sheets include the contents under the copyright of sharp corporation (?sharp?]. please keep them with reasonable care as important information. please don?t reproduce or cause anyone reproduce them without sharp?s consent. 2. please obey the instructions mentioned below for actual use of this device. sharp takes no responsibility for damage caused by improper use of the devices. (i) this device is designed for general electronic equipment. main uses of this device are as follows; [ * computer - oa equipment - telecommunication equipment (terminal) - measuring equipment l tooling machine - av equipment l home appliance, etc. 1 (2) please take proper steps in order to maintain reliability and safety, in case this device is used for the uses mentioned below which require high reliability. - [ unit concerning control and safety of a vehicle (air plane, train, automobile etc.) - traffic signal * gas leak detection breaker * fire box and burglar alarm box * other safety equipment, etc. 1 (3) please do not use for the uses mentioned below which require extremely high reliability. - space equipment [ * telecommunication equipment (trunk) * nuclear control equipment * medical equipment etc. 1 contact a sharp representative of sales office in advance when you intend to use s?%4.rp devices for any applications other than those applications for general electronic equipment recommend by sharp at (1). customer?s approval date presented by date by t. matsumura, department general manager of engineering dept.,11 opto-electronic devices div. elecom group sharp corporation
sharp corporation 1 i november 28. 1995 1 1. application this specification applies to the outline and characteristics of photocoupler model no. pc8 17series. 2. outline refer to the attached drawing no. cy7073k02. 3. ratings and characteristics refer to the attached sheet, page 3 to 6. 4. reliability refer to the attached sheet, page 7. 5. incoming inspection refer to the attached sheet, page 8. 6. supplement 6.1 isolation voltage shall be measured in the following method. (11 short between anode to cathode on the primary side and between collector to emitter on the secondary side. (21 the dielectric withstand tester with zero-cross circuit shall be used. (3) the wave form of applied voltage shall be a sine wave. (it is recommended that the isolation voltage be measured in insulation oil.)
sharp corporation 6.2 business dealing name (? 0? mark indicates business dealing name of ordered product) ordered business rank mark ic (ma) nroduct dealingname 0 pc817xl a, b, c, d or no mark 2.5 to 30 pc817xil a 4.0 to 8.0 pc8 17xi2 b . 6.5 to 13 pc8 17xi3 c 10to20 pc8 17xi4 d PC817XI5 aorb pc8 17xi6 b or c 15 to 30 4.0to 13 : 6.5 to 20 i i 1 pc817xi7 1 c or d 1 10 to 30 pc8 172u8 pc8 17xi9 a, b or c b, cord 4.0 to 20 6.5 to 30 i i 1 pc817xio 1 a, b, c or d 1 4.oto30 6.3 this model is approved by ul. approved model no. : pc8 17 ul file no. : e64380 6.4 this product is not designed against irradiation. this product is assembled with electrical input and output. this product incorporates non-coherent light emitting diode. test conditions 1,=5ma vc,=5v ta=25?c 7. notes refer to the attached sheet- 1 - 1, 2.
ta=25?c l 1 forward current collector current ic 50 ma *l collector power dissipation pc 150 mw *l total power dissipation ptot 200 mw *3 isolation voltage viso 5 kvrms operating temperature topr -30 to +loo ?c storage temperature tstg -55 to +125 ?c *4 soldering temperature tsol 260 ?c ?1 the derating factors of absolute maximum ratings due to ambient temperature are shown in fig. 1 to 4. *2 pulse width_iloo ,us, duty ratio : 0.001 (refer to fig. 5) *3 ac for 1 min, 40 to 6o%rh l 4 for 10s
sharp corporation 3.2 electra-optical characteristics r input output transfer charac- teristics parameter syllhl condition min. typ. max. unit forward voltage vf ifi,=20ma 1.2 1.4 v peak forward voltage vfm im=0.5a 3.0 v reverse current 1, v,=4v 10 pa - terminal capacitance ct v=o, f=lkhz 30 250 pf dark current ke0 vc,=20v, if=0 :- - 100 na collector-emitter bvceo ic=o. 1ma 35 - - v breakdown voltage if.=0 emitter-collector bveco i,=10 /la, i,=0 6 - - v breakdown voltage collector current collector-emitter saturation voltage isolation resistance ic i,=5ma.vce=5v 2.5 - 30 ma v cefsat) 1,=2oma 0.1 0.2 v ic=lma r is0 dc500v 5xlo?o 1o?l - q 40 to 6o%fw floating capacitance cf cut-off frequency fc v=o, f=lmhz vc,=5v, ic=2ma - r,=loo r, -3db 0.6 1.0 pf 80 - khz rise time fall time tr vc,=2v 4 18 pus ic=2ma lf r,=loo r 3 18 pus
rank mark mark l 2 i 6. 5?0.5 1 7. 62ro- 3 1 pin nos. and internal cdnnection diagram d 2 d t 1. oy 10. oz. 1. 5 1 l-j 2. 54 $0.25 unit: l/l mm l 2) factory identification mark shall be or shall not be marked. pc817
sharp corporrtion (fig. 1) forward current vs. ambient temperature -30 0 25 55 75 100 125 ambient temperature ta ( ?c ) (fig. 3) collector power dissipation vs. ambient temperature -30 0 25 50 75 100 125 ambient temperature ta ( ?c ) (fig. 5) peak forward current z .5 vs. duty ratio 2 2000 1000 i 500 2 200 ; 100 m? 50 z 2 20 y 10 2 5 lo-?2 5 lo?2 5 lo-?2 5 10? e duty ratio (fig. 2) diode power diss&iok<->, vs. ambient temperature -.. 5 80 2 70 .+ i 60 p t; 40 3 & 4 20 -30 0 25 55 75 100 125 ambient temperature ta ( ?c ) (fig. 4) total power dissipation vs. ambient temperature r -30 0 25 50 75 100 125 ambient temperature ta (?c ) pulsewidths ps ta=25?c j
sharp corporation 4. reliability the reliability of products shall be satisfied with items listed below. confidence level : 90% ltpd: 10%/20% test items test conditions $1 solderability ?2 soldering heat terminal strength (tension) terminal strength (bending) *3 mechanical shock 23o?c, 5 s 260c. 10 s weight : 5n 5 s/each terminal weight : 2.5n 2 times /each terminal 15000m/s2, 0.5ms 3 times/ tx, +y, fz direction variable frequency vibration 100 to 2000 to 1oohz/4min 200m/s2 4 times/ x, y, 2 direction temperature 1 cycle -55 ?c to t 125c cycling (30mir-i) (30mi.n) 20 cycles test high temp. and high +6o?c, 9o%rh, loooh humidity storage high temp. storage +125?c, loooh low temp. storage -55?c, 1 oooh operation life i,=soma, ptot=200mw ta=25?c, 1 oooh *l test method, conforms to jis c 7021. failure judgement criteria u v,>ux 1.2 i,>uxz icso >?ux2 rc ? ? ? o2 upper specification limit l : lower specification limit ?2 solder shall adhere at the area of 95% or more of immersed portion of lead and pin hole or other holes shall not be concentrated on one portion. samples (nl defective(c) n=ll, c=o n=ll, c=o n=ll, c=o n=ll, c=o n=ll, c=o n=ll, c=o n=22,c=o n=22,c=o n=22 ,c=o i-i=22 ,c=o n=22.c=0 *3 terminal bending direction is shown below.
5. incoming inspection 5.1 inspection items (11 electrical characteristics v,, i,, i,,, vce:(satj, ic, r,,, visa (2) appearance 5.2 sampling method and inspection level a single sampling plan, normal inspection level ii based on is0 2859 is applied. the aql according to the inspection items axe shown below. defect inspection item aql (%) - sharp corporation
1 for cleaning shflrp corporation precautions for photocouplers (1) solvent cleaning : solvent temperature 45c or less immersion for 3 min or less (2) ultrasonic cleaning : the affect to device by ultrasonic cleaning is different by cleaning bath size, ultrasonic power output, cleaning time, pwb size or device mounting condition etc. please test it in actual using condition and con&m that doesn?t occur any defect before starting the ultrasonic cleaning. applicable solvent : ethyl alcohol, methyl alcohol freon te * tf. difion-solvent s3-e please refrain form using chloro fluoro carbon type solvent to clean device as much as possible since it is internationally restricted to protect the ozonosphere. before you use alternative solvent you are requested to confirm that it does not attack package resin. 2. the led used in the photocoupler generally decreases the light emission power by operation. in case of long operation time, please design the circuit with considering the degradation of the light emission power of the led. (50% / 5years)
( 11 if solder refiow : it is recommended that only one soldering be done at the temperature and the time within the temperature profile as shown in the figure. 230t 200c 180c 25c i - 3. precaution for soldering photocoupler (2) other precautions an infbared iamp used to heat up for soldering may cause a localized temperature rise in the resin. so keep the package temperature within that specified in item (1). also avoid immersing the resin part in the solder. shflrp corporrtion

▲Up To Search▲

Price & Availability of PC817XI5

	To Download PC817XI5 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .